LG FBNC608RSA0 Manual de usuario

CEILING DUCT TYPE AIR CONDITIONERSINSTALLATION INSTRUCTIONS(Refrigerant : R407C)P/No.: (Side)(Rear)Air intakeventsAir outletventsControl CoverConnect

WIERED REMOTE CONTROLLER INSTALLATION• Since the room temperature sensor is in the remote controller, the remote controller boxshould be installed in

11Flared connection (Union)Flared connection(Service valve, Ball valve)Use a seemliness tubeFactory chargedIndoorOutdoorREFRIGERANT PIPINGINSTALLATION

Control terminal boardCordclamperCover controlMain terminal boardOutdoorIndoorControl terminal boardControl boxControl box cover(On which the Electric

OutdoorIndoorControl terminal boardControl boxControl box cover(On which the ElectricWiring Connection is put)A A viewRemotecontrol cordConnectioncord

143-1. Preparation of Piping3. Connecting Pipes to the Indoor UnitMain cause of gas leakage is defect inflaring work. Carry out correct flaring workin

6) Pipe bendingAnnealed copper pipe with small diameter (ø6.35 or ø9.52) can be easily bent manually. Inthis case, secure large R(radius) for the bend

1) Connecting the pipes to theOutdoor unit1. Align the center of the pipings andsufficiently tighten the flare nut withfingers.2. Finally,

1) Connecting cables to the Indoor Unit Connect the wires to the terminals on the control board individually according to theoutdoor unit connection.

3) Connecting the cable to theOutdoor Unit1. Remove the Cover control from the unitby loosening a screw.Connect the wires to the terminals onthe contr

4) Form the pipings 1. Wrap the connecting portion of indoorunit with the Insulation material andsecure it with two Plastic Bands. (for ther

1. The following should be always observed for safety ...32. Installation of Indoor, Outdoor unit3. Connecting Pipes to the

7. Air Purging of the Connecting Pipes and the Indoor UnitIndoor unitOutdoor unitLiquid sideCLOSEOPENVaccum pumpGas sideClosedClosed2-way valve/3-way

It operates maximum 16 Units by only one Wired Remote Controller,and each Unit starts sequentially to prevent overcurrent.Operation unitZONE1 2 3 4Hum

Open the rear cover of the wired remote-controller to set the mode.Select one of three selectable modes as follows.Without Zone System1. Position V-H,

Procedure of RPM change:Ex) External Static Pressure is 6mmAq for Model Name "FB-C186HSA0"• To protect the unit, compressor is designed to b

24[Table. 1]4 6 8 10Model Name Step CMM(CFM)Hi 16.0(565) - -Med 14.5(512) - -Lo 13.0(459) - -Hi 18.0(636) - -Med 16.5(583) - -Lo 14.0(494) - -Hi 28.0(

31. The following should be always observed for safety• Please report to or take consent by the supply authority before connecting to the system.• Be

1. Selection of the best location1) Indoor unit Select locationInstall the air conditioner in the location thatsatisfies the following conditions.• Th

2. Indoor unit installation Installation of UnitInstall the unit above the ceiling correctly.• Apply a joint-canvas between the unit andduct to absorb

6• Select and mark the position for fixingbolts.• Drill the hole for set anchor on the faceof ceiling.• Insert the set anchor and washer ontothe suspe

CeilingCAUTION1~3mmDrainage holeDrainage holeU-TrapBCA ≥ 70mmB ≥ 2CC ≥ 2 x SPSP = External Pressure(mmAq)Ex) External Pressure= 10mmAqA ≥ 70mmB ≥ 40mm

8• Drill the piping hole with 70mm dia, holecore drill.• Piping hole should be slightly slant to theoutdoor side.INSULATION, OTHERSInsulate the joint

INSTALLATION OF REMOTE CONTROL BOXInstall the remote control box andcord correctly.• Although the room temperature sensor is in the indoor unit, the r