LG LNB5110 Manual de usuario Pagina 17

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 38
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 16
Operation and settings 17
Image
> Noise Reduction: If pictures are not clear due to noise, this
option would reduce the noise of picture. When you use this
function, the afterimage may occur.
> Color Saturation: Set the intensity of the color.
> Sharpness: The degree to which the boundary of the two
portions is clearly distinguished. If you set the sharpness
value to higher, the image outline becomes sharp. If you set
to lower value, the image outline becomes dim.
> Privacy Mask
- Add: Click the [Add] button.
1. When you click on the preview screen, yellow cross
point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
Note:
• When you select all of 4 points, area is set
automatically.
• To set the Privacy Mask area, each four vertex must
be convex. If the one of 4 vertex is inside to make
concave area, the Privacy Mask area will not be set.
• You can cancel the point by click the mouse right
button near the other point.
• Up to 4 zone is available to set.
- Delete: Delete the selected zone.
- Delete All: Delete all of the mask zone.
- Save: Save the settings of the Privacy Mask.
Note:
• If the privacy mask setting is changed , it is not applied
immediately. You need to click the [Save] button to save
the settings.
• When the [Image] tab is selected, the Privacy Mask area
is displayed on the preview window.
• Set the [Privacy Mask] after complete the [Install]
settings.
• Privacy Mask settings area is not maintained by the
screen change by the operation of Pan / Tilt / Zoom.
When reset the Pan / Tilt / Zoom, you need to reset the
Privacy Mask settings area also.
• If the [D-Effect] is changed, the [Privacy Mask] settings
will be initialized.
• The [EIS] and [Privacy Mask] can not be used at the same
time.
• Default: Click this button to restore the IP device back to original
factory settings.
Stream
Profile
Select the stream [Profile1], [Profile2], [Profile3] or [Profile4]
depending on Install Preset.
Note:
It is displayed the constraints according to the current preset
settings by mouse-over at the right-top of the current Preset.
- LND5110 / LNV5110R / LND5110R / LNU5110R / LNB5110 series
Profile Profile1 Profile2 Profile3 Profile4
Quad
Stream
SXGA @
30 fps
SXGA @
30 fps
SXGA @
30 fps
CIF @ 30 fps
Triple
Stream
SXGA @
30 fps
D1 @ 30 fps
SXGA @
30 fps
N/A
Pivot
SXGA @
30 fps
D1 @ 30 fps CIF @ 30 fps N/A
High
Framerate
SXGA @
60 fps
D1 @ 60 fps N/A N/A
- LNB7210 / LNV7210 / LND7210 /
LNV7210R / LND7210R / LNU7210R series
Profile Profile1 Profile2 Profile3 Profile4
Quad
Stream
1 080P @
30 fps
1 080P @
15 fps
720P @
30 fps
CIF @ 30 fps
1 080P @
30 fps
720P @
30 fps
720P @
30 fps
CIF @ 30 fps
Triple
Stream
1 080P @
30 fps
1 080P @
15 fps
720P @
30 fps
N/A
1 080P @
30 fps
720P @
30 fps
720P @
30 fps
N/A
Pivot
1 080P @
30 fps
N/A N/A N/A
1 080P @
15 fps
720P @
30 fps
CIF @ 30 fps N/A
720P @
30 fps
720P @
30 fps
CIF @ 30 fps N/A
High
Framerate
1 080P @
60 fps
N/A N/A N/A
720P @
60 fps
D1 @ 60 fps N/A N/A
> Enable: Click to activate the stream function.
> Video codec: Select the video mode (Codec) from the drop-
down list. The viewer can choose among MJPEG, H.264 and
H.264_HIGH.
> Resolution: Select the resolution from the drop-down list.
> Maximum frame rate: Set the frame rate of the image.
Note:
Refer to the table below for the supported Framerate.
If you enter the unsupported framerate, the less Encoding
Framerate than the input is applied.
For example, when 17 fps is entered, 15 fps will be applied.
Encoding
Framerate
Sensor Framerate
60 50 30 25
60 O N/A N/A N/A
50 O O N/A N/A
30 O O O N/A
25 O O O O
20 O O O O
15 O O O O
Vista de pagina 16
1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 37 38

Comentarios a estos manuales

Sin comentarios