LG ARUN048GSS4.EWGBLUS Manual de usuario descargar pdf (Pagina 20)

ENGLISH

NOTE

• The figures are based on assumed length of parallel cabling up

to 100m(328ft). For length in excess of 100m(328ft) the figures

will have to be recalculated in direct proportion to the additional

length of cable involved.

• If the power supply waveform continues to exhibit some distor-

tion the recommended spacing in the table should be increased.

- If the cable are laid inside conduits then the following point

must also be taken into account when grouping various cable

together for introduction into the conduits

- Power cable(including power supply to air conditioner) and

communication cables must not be laid inside the same

- In the same way, when grouping the power wires and com-

munication cables should not be bunched together.

Current capacity of power cable Spacing

100V or more

10A 300m(11-13/16 inch)

50A 500m(19-11/16 inch)

100A 1,000m(39-3/8 inch)

Exceed 100A 1,500m(59-1/16 inch)

CAUTION

If apparatus is not properly earthed then there is always a risk of

electric shocks, the earthing of the apparatus must be carried out by

a qualified person.

- Use a separate power supply for the Outdoor Unit and Indoor Unit.

- Bear in mind ambient conditions (ambient temperature,direct sun-

light, rain water,etc.) when proceeding with the wiring and connec-

tions.

- The cable size is the minimum value for metal conduit wiring. The

power cord size should be 1 rank thicker taking into account the line

voltage drops. Make sure the power-supply voltage does not drop

more than 10%.

- Specific wiring requirements should adhere to the wiring regulations

of the region.

- Power supply cords of parts of appliances for outdoor use should not

be lighter than polychloroprene sheathed flexible cord.

- Don't install an individual switch or electrical outlet to disconnect

each of indoor unit separately from the power supply.

CAUTION

• Some installation site may require attachment of an earth leakage

breaker. If no earth leakage breaker is installed, it may cause an

electric shock.

• Do not use anything other than breaker and fuse with correct ca-

pacity. Using fuse and wire or copper wire with too large capacity

may cause a malfunction of unit or fire.

WARNING

• Follow ordinance of your governmental organization for techni-

cal standard related to electrical equipment, wiring regulations

and guidance of each electric power company.

• Make sure to use specified cables for connections so that no

external force is imparted to terminal connections. If connec-

tions are not fixed firmly, it may cause heating or fire.

• Make sure to use the appropriate type of overcurrent protection

switch. Note that generated overcurrent may include some

amount of direct current.

Single outdoor unit

Power supply switch

(Switch fuse : ELCB)

Power supply switch

(Switch fuse)

(Main Switch)

Pull Box(Installer Option)

: Single phase of power supply line(L, N)

: Communication line (3 line): Wired remote control

: Communication line (2 shield line):

Between Indoor Unit and Outdoor Unit

Single Phase 3wires

(L1,L2,GND)

Power supply

208/230V, 60Hz

Power supply

1 Phase

208/230V, 60Hz

WARNING

•

Indoor Unit ground wires are required for preventing electrical shock ac-

cident during current leakage, Communication disorder by noise effect

and motor current leakage (without connection to pipe).

• Don't install an individual switch or electrical outlet to disconnect

each of indoor unit separately from the power supply.

• Install the main switch that can interrupt all the power sources in an

integrated manner because this system consists of the equipment

utilizing the multiple power sources.

• If there exists the possibility of reversed phase, lose phase, mo-

mentary blackout or the power goes on and off while the product is

operating, attach a reversed phase protection circuit locally. Run-

ning the product in reversed phase may break the compressor and

other parts.

Field Wiring

Wiring of main power supply and equipment

capacity

Communication and Power Cables

Communication cable

- Types : shielding cable

- Cross section : 1.0~1.5mm

(1.55x10

-3

~2.32x10

-3

)

- Maximum allowable temperature: 140°F

- Maximum allowable cable length: under 1,000m(3,281ft)

Remote control cable

- Types : 3-core cable

Central control cable

Separation of communication and power cables

- If communication and power cables are run alongside each other then

there is a strong likelihood of operational faults developing due to in-

terference in the signal wiring caused by electrostatic and electro-

magnetic coupling.

The tables below indicates our recommendation as to appropriate

spacing of communication and power cables where these are to be

run side by side

Product type Cable type Diameter

ACP

2-core cable

(Shielding cable)

1.0~1.5mm

(1.55x10

-3

~2.32x10

-3

)

AC Smart

2-core cable

(Shielding cable)

1.0~1.5mm

(1.55x10

-3

~2.32x10

-3

)

AC Ez

4-core cable

(Shielding cable)

1.0~1.5mm

(1.55x10

-3

~2.32x10

-3

)

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 28 29

Comentarios a estos manuales

Sin comentarios

LG ARUN048GSS4.EWGBLUS Manual de usuario Pagina 20

Comentarios a estos manuales

Relacionado con productos y manuales para Acondicionadores de aire del sistema de división LG ARUN048GSS4.EWGBLUS